THMOOTHER LED Strip Pre-Drilled White U Channel Diffuser 10-Pack 3.28FT,Surface Mounted Tape Light Aluminum Track with Continuous Silicone Cover. Flush Installed Low Profile (White, 10X3.3FT)
Brand: THMOOTHER
Condition: Used
$4076
$4290
-4.99% Save $214
Updated: 12 hours 8 mins ago
Description
• Pre-Drilled Countersunk Hole (4 Hole/3.3FT) , Tight Fit and Flush Mounted ,Protect the Profile from Scratch by The Mounting Clips ,Easy Installation, Clean Outlook and Professional Extension
• Silica Gel Milky Diffuser is Easily Snapped Into the Channel, It Does Not Only Protect the Exposed Strip From Dust and Moisture but Also Evening and Smooth Out the Lights Well .The Diffuser Is In Whole Length Without Break Between 2 Tracks
• The Channel Can be Trimmed to Required Length Easily by Hacksaw or Grinder,the Cover Can be Cut by Utility Knives and Scissors, The Bracket Can be Used As Extension Connector ,45 Degree Mitre is Supposed For a 90 Degree Corner .
• The Aluminum Track is Designed to Hold the Strip Less Than 12.4mm(0.49’’) Wide Without Salient Point ,It Fit for Vast Majority of 5050 5630 2835 Steady Color ,RGB ,RGBW and Programmable Tape(Not for Hue 2nd)
• The Package Include White Aluminum Channel 3.28FTX10,Milky Flexible Cover X32.8FT ,M3X12/M3X20 Screw And Wall AnchorX40 .End Caps With Hole X10,End Caps Without Hole X 10 Why need a channel with diffuser ?
1.Protect the exposed strip from Dust,Moisture and inadvertent touch,extend the lifespan of the strip
2. Provide a New Professional Clean finish to the exposed fixtures,Take your LED strips to the next level
3. Break up the harshness dots from the led strip without making light too dim, evening out the lights to a fairly smooth glow.
Steps for a DIY Lighting Project
1.Measure the width of the strip ( make sure it is not oversized in the channel ) and test it
2.Trim the channel and cover to a required length by hacksaw or other devices if needed .
3.Fix The Clips into The working surface By Screw and Press the Channel Into Clips
4.Peel off the sticky at the back of the strip ,lay the strip in the channel
5.Snap the cover into the slot and Press From 1 side to another ,fix the end caps if needed
6.Wiring
Packing details
1.3.28FT/100CM White Aluminum Channel -10 pieces
2.Silicone Milky Cover -32.8 FTX1
3.Stainless Steel Countersunk M3X12 Screw -40 Pieces
4.Carbon Steel Countersunk M3X20 Screw With Wall Anchor -40 Pieces
5.End Cap With Hole -10 Pieces
6.End Cap Without Hole-10 Pieces
• Silica Gel Milky Diffuser is Easily Snapped Into the Channel, It Does Not Only Protect the Exposed Strip From Dust and Moisture but Also Evening and Smooth Out the Lights Well .The Diffuser Is In Whole Length Without Break Between 2 Tracks
• The Channel Can be Trimmed to Required Length Easily by Hacksaw or Grinder,the Cover Can be Cut by Utility Knives and Scissors, The Bracket Can be Used As Extension Connector ,45 Degree Mitre is Supposed For a 90 Degree Corner .
• The Aluminum Track is Designed to Hold the Strip Less Than 12.4mm(0.49’’) Wide Without Salient Point ,It Fit for Vast Majority of 5050 5630 2835 Steady Color ,RGB ,RGBW and Programmable Tape(Not for Hue 2nd)
• The Package Include White Aluminum Channel 3.28FTX10,Milky Flexible Cover X32.8FT ,M3X12/M3X20 Screw And Wall AnchorX40 .End Caps With Hole X10,End Caps Without Hole X 10 Why need a channel with diffuser ?
1.Protect the exposed strip from Dust,Moisture and inadvertent touch,extend the lifespan of the strip
2. Provide a New Professional Clean finish to the exposed fixtures,Take your LED strips to the next level
3. Break up the harshness dots from the led strip without making light too dim, evening out the lights to a fairly smooth glow.
Steps for a DIY Lighting Project
1.Measure the width of the strip ( make sure it is not oversized in the channel ) and test it
2.Trim the channel and cover to a required length by hacksaw or other devices if needed .
3.Fix The Clips into The working surface By Screw and Press the Channel Into Clips
4.Peel off the sticky at the back of the strip ,lay the strip in the channel
5.Snap the cover into the slot and Press From 1 side to another ,fix the end caps if needed
6.Wiring
Packing details
1.3.28FT/100CM White Aluminum Channel -10 pieces
2.Silicone Milky Cover -32.8 FTX1
3.Stainless Steel Countersunk M3X12 Screw -40 Pieces
4.Carbon Steel Countersunk M3X20 Screw With Wall Anchor -40 Pieces
5.End Cap With Hole -10 Pieces
6.End Cap Without Hole-10 Pieces
Product Details
- SKU:
- awhd-us-b0f8qq5dry
- Model:
- 1707-DK-GJ
- Country:
- US