SINOCMP 101-1025-009 Hydraulic Motor for Eaton Char-Lynn H Series — Open-Box, 9% Off

[🔧] Direct Swap – 2.8 cu/in Displacement: Hydraulic motor 101-1025-009 replaces for Eaton Char-Lynn H Series models with 2.8 cu in/rev (46 cc/rev) displacement . The 2-bolt SAE-A flange mount with 3.25 inch pilot diameter and 4.187 inch bolt circle lets this 101-1025-009 hydraulic motor bolt directly onto agricultural augers, harvesters, and industrial sweepers without modifications. [⚙️] High Speed – 969 RPM with 650 lb-in Torque: H series hydraulic motor delivers 650 lb-in continuous torque at 969 RPM, with max continuous pressure 1800 PSI and intermittent pressure up to 2400 PSI . Max continuous flow 12 GPM, intermittent 14 GPM. The Gerotor spool valve design with three moving parts (gerotor-star, drive, shaft) helps this 101-1025-009 replacement hydraulic motor maintain consistent LSHT (low-speed high-torque) performance. [🛢️] NPTF Dryseal Ports – 1/2-14 Side Ports: For Eaton Char-Lynn style hydraulic motor features 1/2-14 NPTF dryseal side ports for reliable leak-free connections, accepting dryseal fittings per SAE J476A . The NPTF threads on this 101-1025-009 hydraulic motor create seals without additional sealant, saving installation time. No case drain required. [🏗️] Keyed Shaft – 1 Inch with 1/4 Woodruff Key: 101-1025-009 replacement hydraulic motor comes with 1 inch straight keyed shaft, 1/4 inch Woodruff keyway, and 1/4-20 UNC-2B threaded end hole . Cast iron housing with time-tested Char-Lynn drive set features three-zone pressure design and an increased shaft seal for enhanced leak protection. Max operating temperature 180°F, minimum -30°F . [📦] Ready-to-Install – Complete Assembly: Box contains one hydraulic motor 101-1025-009 (H Series specification, primer low gloss black finish, Design Code J/9). Important: Verify 3.25 inch pilot diameter, 2-bolt pattern (4.187 inch bolt circle), and 1 inch keyed shaft before ordering. Flush hydraulic lines prior to installation. Intermittent operation refers to running motor no more than 10% of each minute. Replacement Buna seal kit 60540-000 (009 Design).

Restore High-Speed Medium-Duty LSHT Performance With This 101-1025-009 H Series Hydraulic Motor

Slow agricultural augers, weak harvester performance, and unexpected breakdowns often point to a worn hydraulic motor. This replacement hydraulic motor 101-1025-009 brings for Eaton Char-Lynn H Series equipment back to original performance without dealer pricing or long lead times. Designed as a direct replacement for 101-1025-009, 151-2081, and 101-1025 models, this Gerotor spool valve motor delivers the 650 lb-in torque and 969 RPM speed your high-speed medium-duty LSHT (low-speed high-torque) applications demand.

Why H Series Spool Valve Design Matters

This 101-1025-009 replacement hydraulic motor uses the time-tested for Char-Lynn drive set with only three moving components (gerotor-star, drive, and shaft). With hydrodynamic journal bearings optimized for long life, these spool valve motors distribute pressurized fluid via integrated valve slots into the Gerotor orbit gear set. This results in a spool valve section that can be optimized for low-flow low-speed requirements, keeping equipment performing smoothly. Key advantages include:

• Time-tested for Char-Lynn drive set – Optimized drive running angle for reduced wear and extended service life
• Three-zone pressure design – Inlet, return, and case zones optimize performance and sealing under pressure
• Extended bearing life – Hydrodynamic journal bearings at rated loads
• Increased shaft seal – Enhanced leak protection for demanding applications
• Instant shaft reversal – Simply change direction of flow through the motor
• Smooth operation – Stable performance across the entire speed range

Direction of shaft rotation and shaft speed can be controlled easily and smoothly throughout the speed range of the motor.

Complete Specifications

• Model Number: 101-1025-009 / 151-2081 / 101-1025
• Model Code: MH0028AA01AB0000000000000AJ00J
• Series: H Series
• Type: Spool Valve Gerotor Hydraulic Motor
• Displacement: 2.8 cu in/rev (46 cc/rev)
• Max Continuous Pressure: 1800 PSI (124 bar)
• Max Intermittent Pressure: 2400 PSI (165 bar)
• Max Continuous Flow: 12 GPM (45 L/min)
• Max Intermittent Flow: 14 GPM (53 L/min)
• Max Continuous Speed: 969 RPM
• Max Continuous Torque: 650 lb-in (73 Nm)
• Max Intermittent Torque: 876 lb-in (99 Nm)
• Mounting Type: 2-Bolt SAE-A Standard Flange
• Pilot Diameter: 3.25 inch (82.55 mm)
• Pilot Depth: 0.120 inch (3.05 mm)
• Bolt Circle: 4.187 inch (106.35 mm)
• Mounting Hole Size: 0.535 inch (13.59 mm)
• Shaft Type: 1 inch straight keyed, Woodruff key, 1/4-20 UNC-2B threaded end
• Keyway Size: 0.25 inch (6.35 mm)
• Shaft Length: 1.75 inch (44.45 mm)
• Ports: 1/2-14 NPTF dryseal side ports, accepts fittings per SAE J476A
• Case Drain: None
• Rotation: Standard Rotation
• Housing: Cast iron, primer low gloss black paint, 2 mils min
• Min Oil Viscosity: 100 SUS at operating temp
• Recommended Viscosity: 100-200 SUS (20-43 cSt) at operating temp
• Recommended Filtration: ISO 4406 cleanliness code 18/13
• Max Operating Temp: 180°F (82°C)
• Min Operating Temp: -30°F (-34°C)
• Overall Length: 6.45 inch (163.8 mm)
• Overall Height: 3.87 inch (98.3 mm)
• Overall Width: 5.27 inch (133.9 mm)
• Weight: 11.2-12.0 lbs (5.1-5.4 kg)
• Design Code: J (Nine/009)

Compatibility Information

This 101-1025-009 hydraulic motor serves as a replacement for Eaton Char-Lynn H Series applications. It is compatible with the following configurations:

• 101-1025-009 (primary model number)
• 151-2081 (alternate model number)
• 101-1025 (base model)
• 2-Bolt SAE-A flange with 3.25" pilot, 1" keyed shaft specification
• 2.8 cu in displacement, 12 GPM max flow specification

Replacement & Repair Information (009 Design):

• Replacement for Buna Seal Kit (009): 60540-000
• Replacement for Viton Seal Kit (009): 60545-000
• Replacement for Gerotor (009): 8277-001
• Replacement for Drive (009): 602-000
• Replacement for Output Shaft (009): 7360-001
• Replacement for Rear Housing (009): 22230-002
• Replacement for Needle Thrust Bearing: 7537-000
• Replacement for Short Cap Screw (Mounting End): 16292-088 (4 required)
• Replacement for Long Cap Screw (Cap End): 16294-150 (7 required)
• Repair Manual: #7-117
• Repair Parts Drawing: #6-121
• Shaft pressure seal installation tool: 600523
• Seal sleeve or bullet: 600304

Order With Confidence

Downtime costs money. Keep a spare 101-1025-009 hydraulic motor on your service truck or in your parts room. Click add to cart now and restore the reliable high-speed medium-duty LSHT performance your agricultural, industrial, or food processing equipment demands.