Replacement for Sayco 06550 Diverter Stem for 308 T-308 Tub and Shower — Open-Box, 5% Off
Brand: FOURHOME
Description
FITS SAYCO 308 AND T-308: Middle-handle diverter stem compatible with Sayco OEM 06550 for 308 and T-308 three-handle compression tub and shower valves. Restores full diversion between the tub spout and the showerhead from the center handle.
FIXES FAILED DIVERSION: Use when water leaves the tub spout and the showerhead at the same time, the spout keeps dripping while the shower runs, water seeps around the middle handle base, or the diverter handle has gone stiff and grinding. A worn barrel seal on the original stem is the usual cause.
SPECS AND WHAT SHIPS: Machined brass diverter stem, 4-11/16 inches overall, with a 16-point splined broach at the handle end and a sealing barrel that engages the brass cross-tee inside the valve body. The barrel seal is installed at the factory. One stem ships in the box.
POSITIVE IDENTIFICATION: Your old part is a brass stem about 4-11/16 inches long with a 16-point splined tip and a sealing barrel at the bottom rather than a flat bibb washer. It comes out of the center position of a three-handle Sayco trim. Measure from broach tip to barrel end and count the splines before ordering.
SAYCO OEM FAMILY: Compatible with Sayco OEM 06550 in the center diverter position of the 308 and T-308 valve. The outer handles on the same valve take the hot stem, OEM P002, on the left and the cold stem, OEM P004, on the right, both stocked separately by FourHome so the full three-handle valve can be rebuilt in one order.
AFTERMARKET CROSS REFS: Serves the same repair as Danco 9B-5D (15886B) and BrassCraft ST2684, both catalogued at 4-11/16 inches for Sayco 308 and T-308 bath faucets. Match your old stem against those numbers or against Sayco OEM 06550 before ordering.
TRADE AND PROPERTY MAINTENANCE: A stock item for property management companies, multifamily operators, hospitality maintenance teams, schools, and service plumbers keeping older Sayco three-handle valves in service. Available to Amazon Business customers for multi-unit and recurring orders.
INSTALLS IN 15 TO 20 MINUTES: Shut off the water, then bleed the pressure through the tub spout before you pull the old stem, because the barrel sprays back the moment it clears the valve body. Pull the middle handle and escutcheon, back the stem out with a deep stem socket or stem wrench, and thread the new one in. Tools: deep stem socket, adjustable wrench, flathead screwdriver.
FOURHOME QUALITY: Broach spline count, overall length, and barrel diameter are dimensioned against the published Sayco stem, so the diverter seats in the valve body and indexes the handle without modification. Brass body with the barrel seal fitted at the factory rather than a field-cut O-ring.
VERIFY BEFORE ORDERING: Center diverter position only. This is not the hot stem, OEM P002, or the cold stem, OEM P004, which carry a flat bibb washer instead of a barrel seal. It is not the shorter 4-1/16 inch Sayco K-1 diverter stem sold as Everbilt 86011. Not for two-handle Sayco faucets, pressure-balance valves, ceramic disc cartridges, or single-handle cartridges.
When a three-handle Sayco 308 or T-308 tub and shower faucet sends water out of the tub spout and the showerhead at the same time, keeps dripping from the spout while the shower runs, or fights back with a stiff, grinding middle handle, the worn part is almost always the barrel seal on the diverter stem. This is the middle-handle diverter stem compatible with Sayco OEM 06550, and it restores clean diversion between spout and showerhead without replacing the valve body or opening the wall. The stem is machined from brass, 4-11/16 inches overall, with a 16-point splined broach at the handle end and a sealing barrel that engages the brass cross-tee inside the valve body. The barrel seal is fitted at the factory. One stem ships in the box. This part is compatible with Sayco OEM 06550 in the center position of the 308 and T-308 valve, and it serves the same repair as Danco 9B-5D (15886B) and BrassCraft ST2684, both catalogued at 4-11/16 inches for the same faucets. The outer handles on the same valve take the hot stem, OEM P002, and the cold stem, OEM P004, both stocked separately by FourHome for full three-handle rebuilds. This is not a hot or cold stem, those carry a flat bibb washer rather than a barrel seal, and it is not the shorter 4-1/16 inch Sayco K-1 diverter stem sold as Everbilt 86011. It does not fit two-handle Sayco faucets, pressure-balance valves, ceramic disc cartridges, or single-handle cartridges. Measure your old stem from broach tip to barrel end and confirm 4-11/16 inches with a 16-point broach before ordering. Plan on 15 to 20 minutes. Shut off the water, then bleed the pressure through the tub spout before pulling the old stem, because the barrel sprays back the moment it clears the valve body. Pull the middle handle and escutcheon, back the stem out with a deep stem socket or stem wrench, and thread the new one in. While the stem is out, look at the bonnet packing nut threads, the cross-tee bore the barrel rides in, and the handle index button. A worn cross-tee bore is a common reason diversion still fails after a stem swap. Step-by-step guidance is shown in the listing images. FourHome builds aftermarket repair parts for faucet systems long out of production but still in service. Broach spline count, overall length, and barrel diameter on this stem are dimensioned against the published Sayco part so it seats and indexes without modification. Overall length 4-11/16 inches, 16-point broach, factory-fitted barrel seal.
Sold by
Amazon Warehouse
Official Amazon outlet for open-box & returned items
- Backed by Amazon's A-to-Z Guarantee
- 30-day return policy
- Ships from Amazon fulfillment centers
- Price verified on Amazon
Product Details
- SKU:
- awhd-us-b0gyg2d66h
- Model:
- 4H2615953
- Country:
- US
- ASIN:
- B0GYG2D66H
Shopping Smarter
Common questions about buying open-box and refurbished.




















