CNCTOPBAOS 4 Axis Nema23 Stepper Motor USB Mach3 CNC Kit,270oz-in 76mm 3A,USB Controller Board Motion Control Card,TB6600 Driver 4.5A 24V for CNC Router Milling Engraving Machine

Model: 23HS8430 Nema23 Stepper Motor; Holding Torque: 270oz-in 180N.cm; Motor Size:57x57x76mm; Phase: 2 phase; 1.8° Step Angle; Type:Hybrid; Shaft: Dia 8mm Single shaft; Wiring: A+ : Red; A- : Green; B+ : Yellow; B- : Blue Driver: TB6600 driver Voltage: DC 10V-45V; Current: rated maximum output reaches: ±4.5A ; Subdivision: full step, half step, 1/4 step, 1/8 step, 1/16 step, maximum 16 subdivisions 4 Axis USB Mach3 Motion Control Board: USB port is applicable to any netbook, notebook, desktop, tablet and other PC compatible computers with USB interface.This control board does not require any drivers to be installed. As long as Mach3 can run, the control card can be used; Support computer system:Windows 2000/ XP / Windows 7/8/10 350W 24V DC Switching Power Supply: AC input voltage range: 110V-120V AC or 220V-240V AC; selected by switch to choose input voltage Functions of the Mach3 Control Board: It supports 4-axis linkage control at most; Max step-pulse frequency is 100KHz;Support probe tool,E-stop input,Limit switches;Support for electronic handwheel; Support spindle control PWM and relay mode

Paccel include:

4× Nema23 23HS8430 stepper motor 76mm 3A

4× TB6600 stepper motor driver

1× 4 Axis USB Mach3 control board

1× USB Cable

1× CD disc

1× 350W 24V DC switching power supply

Nema23 Stepper motor:

* Motor Type: Hybrid Stepper 

* Step Angle: 1.8 deg. 

* Holding Torque: 1.8Nm (270oz.in) 18kg.cm

* Phase Resistance: 1ohms 

* Rated Current/phase: 3A 

* Inductance:3.5mH+/-20%(1KHz) 

* Frame Size: 57x57x76 mm 

* Number of Leads: 4

* Weight: 1.1kg 

* Shaft:8mm diameter single shaft

* Wiring:

A+ : Red ; A- : Green ; B+ : Yellow ; B- : Blue

TB6600 stepper motor driver 4.5A

The working voltage is DC 10V-45V.

The rated maximum output reaches: ±4.5A.

Suitable for 42, 57, 86 two-phase/four-phase/four-wire/six-wire stepper motors within 4.2A.

Subdivision: full step, half step, 1/4 step, 1/8 step, 1/16 step, maximum 16 subdivisions.

Mach3 USB motion control board 4 axis

It is recommended that the limit switch and emergency stop switch must be installed first and can be used normally.

Feature:

This USB motion card does not need install any USB driver,Windows2000/XP/Windows7/8,can directly identify.

4-axis linkage, Maximum step-pulse frequency: 100KHz, support connect four stepper motor drives or servo drives.

Signal Output:0-10V, it can control the spindle motor speed through using mach3 software.

4 general-purpose opto-couplers isolation input

350W 24V DC switching power supply

DC output: 24V 0-14.5A ; AC input voltage range: 115VAC/6.5A/50HZ or 230VAC/3.4A/60HZ; Selected by switch