ACA56078801 Washer Door Boot Spring Clamp for Front Load Washers — Open-Box, 30% Off

WIDE COMPATIBILITY — Direct replacement for OEM part numbers ACA56078801, ACA56078802, AP4998833, AH3530864, EA3530864, PS3530864, 4861EN3004L and 1525271. Fits LG, Kenmore and Maytag front-load washers, including popular LG models WM2601HL/HR/HW, WM3001/3070/3150/3250/3360/3885 series and Kenmore 796.41/42/43 series. Check your old ring or owner's manual to confirm fitment before ordering. STOPS WATER LEAKS — This door boot retaining ring locks the gasket firmly against the washer tub, restoring a tight, watertight seal. A worn or stretched clamp lets water escape during wash cycles — replacing it stops floor leaks, loose boot seals and trapped-moisture odors, keeping your laundry room dry. DURABLE SPRING STEEL BUILD — Crafted from high-quality spring steel with a corrosion-resistant coating to withstand constant moisture, detergent exposure and temperature swings inside front-load washers. Heat-treated flexible structure maintains strong clamping force over time, even in humid environments. EASY DIY INSTALLATION — Simple swap-out repair with basic tools: (1) Unplug the washer and wear gloves; (2) Release spring tension on the old clamp; (3) Seat the new ring into the gasket lip and tub channel; (4) Evenly tension the spring for a snug fit; (5) Run a test cycle to confirm the seal. No plumber needed. WHAT YOU GET & SUPPORT — Each package includes 1 washer door boot spring clamp. If you have fitment or installation questions, our team responds within 24 hours.

Restore a Leak-Free Seal with the ACA56078801 Washer Door Boot Spring Clamp

Is your front-load washer leaving puddles on the laundry room floor? A stretched, rusted, or fatigued door boot retaining ring is often the culprit. This outer door boot seal clamp locks the door gasket (bellow) firmly against the washer tub, rebuilding a watertight seal that holds through every fill, agitate, and high-speed spin cycle. Replace the clamp — not the whole gasket — and stop water leaks, loose boot seals, and trapped-moisture mildew odors before they ruin your floor.

Direct OEM Replacement — Cross-Reference Part Numbers

This washer clamp assembly is a direct replacement for the following OEM and aftermarket part numbers:

ACA56078801 · ACA56078802 · AP4998833 · 4861EN3004L · 1525271 · AH3530864 · EA3530864 · PS3530864

Full Compatibility List — LG, Kenmore & Maytag Front-Load Washers

Compatible with LG models:41262, 41303, 41392, 48231009799, 48231010108, WM2601HL, WM2601HR, WM2601HW, WM2701HV, WM2801HLA, WM2801HRA, WM2801HWA, WM2901HVA, WM3001HPA, WM3001HRA, WM3001HWA, WM3050CW, WM3070HRA, WM3070HWA, WM3150HVC, WM3150HWC, WM3170CW, WM3250HRA, WM3250HVA, WM3250HWA, WM3360HRCA, WM3360HVCA, WM3360HWCA, WM3370HVA, WM3370HRA, WM3485HWA, WM3670HVA, WM3700HVA, WM3770HWA, WM3875HVCA, WM3885HCCA, WM3885HWCA, WM4070HVA, WM8000HWA, WM9000HVA, LSWF388HVS, and more.

Compatible with Kenmore / Sears models:79640512900, 79640518900, 79641022900, 79641028900, 79641029900, 79641073310, 79641162410, 79641162411, 79641182310, 79641182311, 79641262610, 79641282310, 79641282311, 79641283310, 79641302610, 79641303610, 79641382410, 79641382411, 79641383410, 79641383411, 79641549110, 79641572210, 79641573210, 79641722010, and more.

Also fits many Maytag front-load washer models. Please verify your old clamp part number or owner's manual before ordering.

Heavy-Duty Spring Steel — Built for Humid, High-Vibration Environments

Premium spring steel wire with a corrosion-resistant coating stands up to constant moisture, detergent residue, and temperature swings inside the washer cabinet.

Heat-treated, anti-fatigue structure maintains consistent clamping tension through thousands of door open/close cycles and spin-cycle vibrations — no loosening, no gaps, no leaks.

High-tension coil spring delivers even, uniform pressure around the full gasket circumference, ensuring the bellow stays seated in the tub channel during every wash.

Easy DIY Installation — No Service Call Needed

1. Unplug the washer from the power outlet and wear work gloves.
2. Release the spring tension on the old outer clamp and remove it from the gasket lip.
3. Seat the new retaining ring into the gasket channel, aligning the spring at the top or bottom per your original layout.
4. Evenly tension the spring until the ring sits snug and flush around the entire door boot.
5. Run a short test cycle with no clothes to confirm a dry, leak-free seal.

Tip: If your gasket itself is torn, swollen, or mildew-cracked, replace the gasket and clamp together for a long-lasting repair.

What's in the Box

1 × Washer Door Boot Spring Clamp (Outer Retaining Ring with Spring)

Satisfaction Promise: If you have fitment or installation questions, our support team responds within 24 hours. Confirm your model using the list above or your old part number before ordering.