Seamax SUP 16DB Electric Air Pump Max 16PSI, Double Stage w/Fast Speed High Pressure, Built in 12V 6AH Lithium Battery and USB 2A 5V Charging Port, Fully Portable W/Dual Charging or Dual Power Mode

• EASY TO POWER : Thanks to the intelligent control system and its newly designed power control unit, the air pump is great to use with the inflatable boat, SUP, and tent. This DC electric air pump can be powered by its built-in 6AH lithium battery after charging or through a standard extremal 12V charger socket in a vehicle. It can quickly reach and automatically stop at the user's pre-set air pressure. • NEW AND SMART : Our Seamax pump has AI smart monitoring feature to help the user reach the highest efficiency pumping. When the pump starts to inflate, the computer monitors the real-time pressure every second, based on our Self-Developed smart pump formula program, it can find the pump the best timing to switch to 2nd The computer also monitors the pump's internal temperature and continued working time, Auto Stop Protection feature has been built-in to protect your pump. • MORE COMPATIBLE : The valve connector with the hose is suitable for SUPs equipped with HR (Halkey-Roberts), Bravo, Naru, or similar type air valves. This kind of air valve has a turning pin or pressing down the pin in the middle to control the valve's Open & Closed position. 3 silicon O-Rings to choose from and keep the connection best airtight. More valve adaptors are available and even fit the Leafield C7 or D7 air valve. • MORE COMPACT AND MORE FEATURES : Fully support Inflation and Deflation; 1st stage max speed 350L/min; 2nd stage max speed 70L/min, Pressure setting increments 0.5 PSI and Max 16PSI.Built-in LED flashlight and 2x USB 5V charging ports, 6Lbs Super lightweight, the pump comes with a storage box to keep the travel charger and car 12Vadadptor, 2 ways to use the pump and charge the battery. A great design travel case to keep the pump and accessories in order. • NOTE OF FIRST TIME USE : Fully charge the battery before use. One charge can inflate up to 3x SUPs or 3x 12ft Inflatable Boat. don't leave the pump in the dusty ground when pumping. The Power Button needs to Press & Hold for 2 seconds to turn on the air pump. The pump will go to sleep mode (turn off) when no use for 2 minutes. 1). Choose the proper fitting for the air valve of your inflatable boat, inflatable kite or paddle board. Put the valve at the inflation position. Attach the correct valve adapter to the inflation hose that comes with your pump. Attach the other end to the pump (smooth round outlet on the pump).

2). Connect the pump’s terminals to the battery paying close attention to the polarity. Make sure the clips are on the same color electrode and properly connected. Otherwise the pump won’t turn on or run properly.

3). Enter the maximum desired pressure by using the set pressure button. The set pressure will be shown on the right hand side of the LCD screen. The pump provides readings in metric (KPa). (Pressure: 10KPa = 100mbr = 1.45 PSI). Factory default working pressure is set at 25KPa (3.6 PSI).This pressure is suitable for most inflatable boats. 45Kpa is 6 PSI to support the inflatable kite.

4). Press the POWER button to start. During inflation, the left hand side of LCD screen should show the pressure that the inflator has reached. As soon as entered set pressure has been reached, the inflator turns off automatically. Take off the air hose from the chamber once the pump stops running. The inflator can be turned off at any time by pressing the POWER button again. It is possible to stop the inflator at any time by pressing this button.

5). The inflator operates in two stages which can be identified by the noise of the turbine at the beginning followed by the piston. The inflator switches from turbine to piston automatically. If the chamber pressure is over 7KPa / 1 PSI, the pump will start the 2nd stage only. If the set pressure is lower than the chamber’s pressure, the pump won’t be started.